Rainbow-electronics DS1875 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Komunikace Rainbow-electronics DS1875. Rainbow Electronics DS1875 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 92
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
General Description
The DS1875 controls and monitors all functions for burst-
mode transmitters, APD receivers, and video receivers.
It also includes a power-supply controller for APD bias
generation, and provides all SFF-8472 diagnostic and
monitoring functionality. The combined solution of the
DS1875 and the MAX3643 laser driver provides APC
loop, modulation current control, and eye safety func-
tionality. Ten ADC channels monitor V
CC
, temperature
(both internal signals), and eight external monitor inputs
(MON1–MON8) that can be used to meet transmitter,
digital receiver, video receiver, and APD receiver-signal
monitoring requirements. Four total DAC outputs are
available. A PWM controller with feedback and compen-
sation pins can be used to generate the bias for an APD
or as a step-down converter. Five I/O pins allow addi-
tional monitoring and configuration.
Applications
BPON, GPON, or EPON Optical Triplexers
SFF, SFP, and SFP+ Transceiver Modules
APD Controller
Features
Meets All PON Burst-Timing Requirements for
Burst-Mode Operation
Laser Bias Controlled by APC Loop and
Temperature Lookup Table (LUT)
Laser Modulation Controlled by Temperature LUT
Six Total DACs: Four External, Two Internal
Two 8-Bit DACs, One of Which is Optionally
Controlled by MON4 Voltage
Internal 8-Bit DAC Controlled by a Temperature-
Indexed LUT
PWM Controller
Boost or Buck Mode
Boost Mode: Uses Optional External
Components, Up to 90V Bias Generation
131kHz, 262kHz, 525kHz, or 1050kHz Selectable-
Switching Frequency
APD Overcurrent Protection Using Optional Fast
Shutdown
10 Analog Monitor Channels: Temperature, V
CC
,
Eight Monitors
Internal, Factory-Calibrated Temperature Sensor
RSSI with 29dB Electrical Dynamic
Five I/O Pins for Additional Control and
Monitoring Functions, Four of Which are Either
Digital I/O or Analog Monitors
Comprehensive Fault-Measurement System with
Maskable Laser Shutdown Capability
Two-Level Password Access to Protect
Calibration Data
120 Bytes of Password-1 Protected Memory
128 Bytes of Password-2 Protected Memory in
Main Device Address
256 Additional Bytes Located at A0h Slave
Address
I
2
C-Compatible Interface for Calibration and
Monitoring
2.85V to 3.9V Operating Voltage Range
-40°C to +95°C Operating Temperature Range
38-Pin TQFN (5mm x 7mm) Package
DS1875
________________________________________________________________
Maxim Integrated Products
1
TOP VIEW
TQFN
(5mm
×
7mm
×
0.8mm)
13
14
15
16
17
18
19
MON5/D0
MON6/D1
MON7/D2
MON8/D3
MON1
MON2
MON4
38
37
36
35
34
33
32
123456789101112
N.C.
N.C.
N.C.
V
CC
SW
GND
GND
LOSI
N.C.
GND
V
CC
TX-D
N.C.
FETG
N.C.
TX-F
SCL
SDA
BEN
31 30 29 28 27 26 25 24 23 22 21 20
N.C.
MON3N
MON3P
DAC1
GND
M4DAC
FB
BIAS
MOD
COMP
BMD
V
CC
+
*EP
*EXPOSED PAD.
DS1875
Pin Configuration
Ordering Information
Rev 1; 10/08
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
+
Denotes a lead-free/RoHS-compliant package.
T&R = Tape and reel.
*
EP = Exposed pad.
PART TEMP RANGE PIN-PACKAGE
DS1875T+ -4C to +95°C 38 TQFN-EP*
DS1875T+T&R -4C to +95°C 38 TQFN-EP*
PON Triplexer and SFP Controller
Zobrazit stránku 0
1 2 3 4 5 6 ... 91 92

Shrnutí obsahu

Strany 1 - Ordering Information

General DescriptionThe DS1875 controls and monitors all functions for burst-mode transmitters, APD receivers, and video receivers.It also includes a p

Strany 2 - TABLE OF CONTENTS

DS1875PON Triplexer and SFP Controller10 ______________________________________________________________________________________SUPPLY CURRENTvs. SUPPL

Strany 3 - TABLE OF CONTENTS (continued)

DS1875Typical Operating Characteristics (continued)(VCC= +2.85V to +3.9V, TA= +25°C, unless otherwise noted.)CALCULATED AND DESIRED % CHANGEIN VMOD vs

Strany 4 - LIST OF TABLES

DS1875PON Triplexer and SFP Controller12 ______________________________________________________________________________________PWM DAC DNLDS1875 toc19

Strany 5 - ABSOLUTE MAXIMUM RATINGS

DS1875PON Triplexer and SFP Controller______________________________________________________________________________________ 13Pin DescriptionPIN NAME

Strany 6 - ANALOG OUTPUT CHARACTERISTICS

DS1875PON Triplexer and SFP Controller14 ______________________________________________________________________________________Block DiagramHBIASQUICK

Strany 7 - PWM CHARACTERISTICS

DS1875Typical Operating CircuitBEN+BEN-DISIN-IN+OUT-BIAS-BIAS+OUT+VCCTX-FTX-DSCLSDALOSID3D0MON[5:7]MON2MON3MON4FETGM4DACD1MON1BMD3.3VVMSETMODSETVREFIM

Strany 8 - ANALOG VOLTAGE MONITORING

DS1875PON Triplexer and SFP Controller16 ______________________________________________________________________________________Detailed DescriptionThe

Strany 9 - C TIMING SPECIFICATIONS

DS1875DC OperationWhen using autodetect mode or closed-loop mode,BEN should be equal to VCCor long burst. In open-loopmode, BEN should be ground or an

Strany 10 - = +2.85V to +3.9V, T

DS1875PON Triplexer and SFP Controller18 ______________________________________________________________________________________BIAS and MOD Output as

Strany 11

DS1875quick-trip alarm that is detected by default remainsactive until a subsequent comparator sample shows thecondition no longer exists. A second bi

Strany 12

DS18752 _______________________________________________________________________________________Absolute Maximum Ratings . . . . . . . . . . . . . . .

Strany 13 - Pin Description

DS1875PON Triplexer and SFP Controller20 ______________________________________________________________________________________The ADC results (after

Strany 14 - Block Diagram

DS1875Right-Shifting ADC ResultIf the weighting of the ADC digital reading must con-form to a predetermined full-scale value defined by astandard’s sp

Strany 15 - Typical Operating Circuit

DS1875PON Triplexer and SFP Controller22 ______________________________________________________________________________________Safety Shutdown (FETG)

Strany 16 - Detailed Description

DS1875Die IdentificationThe DS1875 has an ID hard-coded to its die. Two regis-ters (Table 02h, Registers 86h–87h) are assigned forthis feature. Byte 8

Strany 17 - Modulation Control

DS187524 ______________________________________________________________________________________Dual-range functionality consists of two modes of opera

Strany 18 - Table 2. Update Rate Timing

DS1875two thresholds. The actual threshold values are a func-tion of the number of right-shifts being used. Table 7shows the threshold values for each

Strany 19 - Monitors and Fault Detection

DS1875PON Triplexer and SFP Controller26 ______________________________________________________________________________________than the PWM DAC level,

Strany 20 - ADC Timing

DS1875Stability and Compensation Component SelectionThe components connected to the COMP pin (RCOMPand CCOMP) introduce a pole and zero that are neces

Strany 21 - Alarm Sources

DS1875PON Triplexer and SFP Controller28 ______________________________________________________________________________________SWCURRENT SINKFBCOMPDS1

Strany 22 - Interface

DS1875SCLNOTE: TIMING IS REFERENCED TO VIL(MAX) AND VIH(MIN).SDASTOP START REPEATEDSTARTtBUFtHD:STAtHD:DATtSU:DATtSU:STOtHD:STAtSPtSU:STAtHIGHtRtFtLOW

Strany 23 - Functionality)

DS1875_______________________________________________________________________________________ 3Die Identification . . . . . . . . . . . . . . . . . .

Strany 24 - Memory Map

DS1875PON Triplexer and SFP Controller30 ______________________________________________________________________________________Byte Write: A byte writ

Strany 25 - PWM Controller

DS1875were not modified during the transaction are stillsubject to a write cycle. This can result in a wholepage being worn out over time by writing a

Strany 26 - Inductor Selection

DS1875PON Triplexer and SFP Controller32 ______________________________________________________________________________________Shadowed EEPROMMany NV

Strany 27 - Digital I/O Pins

DS1875This register map shows each byte/word (2 bytes) in terms of the row it is on in the memory. The first byte in the row islocated in memory at th

Strany 28

DS1875PON Triplexer and SFP Controller34 ______________________________________________________________________________________TABLE 00h WORD 0 WORD

Strany 29 - C Communication

DS1875TABLE 01h (PW1) WORD 0 WORD 1 WORD 2 WORD 3 ROW (HEX) ROW NAME BYTE 0/8 BYTE 1/9 BYTE 2/A BYTE 3/B BYTE 4/C BYTE 5/D BYTE 6/E BYTE 7/F

Strany 30 - C Protocol

DS1875PON Triplexer and SFP Controller36 ______________________________________________________________________________________TABLE 02h (PW2) WORD 0

Strany 31

DS1875TABLE 03h (PW2) WORD 0 WORD 1 WORD 2 WORD 3 ROW (HEX) ROW NAME BYTE 0/8 BYTE 1/9 BYTE 2/A BYTE 3/B BYTE 4/C BYTE 5/D BYTE 6/E BYTE 7/F

Strany 32 - Shadowed EEPROM

DS1875PON Triplexer and SFP Controller38 ______________________________________________________________________________________TABLE 04h (MODULATION L

Strany 33 - Register Descriptions

DS1875TABLE 06h (M4DAC LUT) WORD 0 WORD 1 WORD 2 WORD 3 ROW (HEX) ROW NAME BYTE 0/8 BYTE 1/9 BYTE 2/A BYTE 3/B BYTE 4/C BYTE 5/D BYTE 6/E BY

Strany 34 - Table 00h Register Map

DS1875PON Triplexer and SFP Controller4 _______________________________________________________________________________________Auxiliary Memory A0h Re

Strany 35 - Table 01h Register Map

DS1875PON Triplexer and SFP Controller40 ______________________________________________________________________________________TABLE 08h (BIAS OPEN-LO

Strany 36 - Table 02h Register Map

DS1875AUXILIARY MEMORY (A0h) WORD 0 WORD 1 WORD 2 WORD 3 ROW (HEX) ROW NAME BYTE 0/8 BYTE 1/9 BYTE 2/A BYTE 3/B BYTE 4/C BYTE 5/D BYTE 6/E B

Strany 37 - Table 03h Register Map

DS1875PON Triplexer and SFP Controller42 ______________________________________________________________________________________Lower Memory, Register

Strany 38 - Table 04h Register Map

DS1875Lower Memory, Register 08h to 09h: VCCALARM HILower Memory, Register 0Ch to 0Dh: VCCWARN HILower Memory, Register 10h to 11h: MON1 ALARM HILower

Strany 39 - Table 06h Register Map

DS1875PON Triplexer and SFP Controller44 ______________________________________________________________________________________ FACTORY DEFAULT 000

Strany 40 - Table 08h Register Map

DS1875Lower Memory, Register 30h to 5Fh: PW2 EE FACTORY DEFAULT 00h READ ACCESS All WRITE ACCESS PW2 MEMORY TYPE Nonvolatile (EE)

Strany 41

DS1875PON Triplexer and SFP Controller46 ______________________________________________________________________________________ POWER-ON VALUE 0000h

Strany 42

DS1875Lower Memory, Register 6Eh: STATUS POWER-ON VALUE X000 0XXXb READ ACCESS All WRITE ACCESS See below MEMORY TYPE Volatile

Strany 43

DS1875PON Triplexer and SFP Controller48 ______________________________________________________________________________________ POWER-ON VALUE 00h

Strany 44

DS1875 POWER-ON VALUE 10h READ ACCESS All WRITE ACCESS N/A MEMORY TYPE Volatile 70h TEMP HI TEMP LO VCC HI VCC LO MON1 HI

Strany 45

DS1875Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and funct

Strany 46

DS1875PON Triplexer and SFP Controller50 ______________________________________________________________________________________ POWER-ON VALUE 00h

Strany 47

DS1875Lower Memory, Register 72h: ALARM1 POWER-ON VALUE 00h READ ACCESS All WRITE ACCESS N/A MEMORY TYPE Volatile

Strany 48

DS1875PON Triplexer and SFP Controller52 ______________________________________________________________________________________Lower Memory, Register

Strany 49

DS1875Lower Memory, Register 75h: WARN2 POWER-ON VALUE 00h READ ACCESS All WRITE ACCESS N/A MEMORY TYPE Volatile 75h MON3 HI

Strany 50

DS1875PON Triplexer and SFP Controller54 ______________________________________________________________________________________Lower Memory, Register

Strany 51

DS1875Lower Memory, Register 79h: DIN POWER-ON VALUE See description READ ACCESS All WRITE ACCESS N/A MEMORY TYPE Volatile 7

Strany 52

DS1875PON Triplexer and SFP Controller56 ______________________________________________________________________________________Lower Memory, Register

Strany 53

DS1875Table 00h Register DescriptionsTable 00h, Register 80h to 81h: MON5 VALUETable 00h, Register 82h to 83h: MON6 VALUETable 00h, Register 84h to 85

Strany 54

DS1875PON Triplexer and SFP Controller58 ______________________________________________________________________________________Table 01h, Register F8h

Strany 55

DS1875Table 01h, Register FAh: ALARM1 POWER-ON VALUE 00h READ ACCESS All WRITE ACCESS PW1 MEMORY TYPE Volatile FAh RESER

Strany 56

DS1875PON Triplexer and SFP Controller6 _______________________________________________________________________________________PARAMETER SYMBOL CONDIT

Strany 57

DS1875PON Triplexer and SFP Controller60 ______________________________________________________________________________________Table 01h, Register FDh

Strany 58

DS1875Table 02h Register DescriptionsTable 02h, Register 80h: MODEPON Triplexer and SFP Controller____________________________________________________

Strany 59 - Table 01h, Register FCh: WARN

DS1875PON Triplexer and SFP Controller62 ______________________________________________________________________________________Table 02h, Register 81h

Strany 60 - Table 01h, Register FDh: WARN

DS1875Table 02h, Register 83h: APC DAC FACTORY DEFAULT 00h READ ACCESS PW2 WRITE ACCESS PW2 and APC EN = 0 MEMORY TYPE Volati

Strany 61 - Table 02h, Register 80h: MODE

DS1875PON Triplexer and SFP Controller64 ______________________________________________________________________________________Table 02h, Register 85h

Strany 62

DS1875Table 02h, Register 88h: SAMPLE RATE FACTORY DEFAULT 30h READ ACCESS PW2 WRITE ACCESS PW2 MEMORY TYPE Nonvolatile (SEE)

Strany 63

DS1875PON Triplexer and SFP Controller66 ______________________________________________________________________________________Table 02h, Register 89h

Strany 64 -  (M4DAC + 1)

DS1875Table 02h, Register 8Ah: RESERVEDFACTORY DEFAULT 00h READ ACCESS PW2 WRITE ACCESS PW2 MEMORY TYPE Nonvolatile (SEE) This re

Strany 65

DS1875PON Triplexer and SFP Controller68 ______________________________________________________________________________________Table 02h, Register 8Ch

Strany 66

DS1875Table 02h, Register 8Dh: COMP RANGING FACTORY DEFAULT 00h READ ACCESS PW2 WRITE ACCESS PW2 MEMORY TYPE Nonvolatile (SEE)

Strany 67

DS1875PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS PWM-DAC Full-Scale Voltage VPWM-DAC 1.25 V PWM-DAC Resolution 8 Bits VPWM-DAC

Strany 68

DS1875PON Triplexer and SFP Controller70 ______________________________________________________________________________________Table 02h, Register 8Eh

Strany 69

DS1875Table 02h, Register 92h to 93h: VCCSCALETable 02h, Register 94h to 95h: MON1 SCALETable 02h, Register 96h to 97h: MON2 SCALETable 02h, Register

Strany 70

DS1875PON Triplexer and SFP Controller72 ______________________________________________________________________________________Table 02h, Register A2h

Strany 71

DS1875Table 02h, Register B0h to B3h: PW1 FACTORY DEFAULT FFFF FFFFh READ ACCESS N/A WRITE ACCESS PW2 MEMORY TYPE Nonvolatile (

Strany 72

DS1875PON Triplexer and SFP Controller74 ______________________________________________________________________________________Table 02h, Register B8h

Strany 73

DS1875Table 02h, Register B9h: FETG ENABLE0 FACTORY DEFAULT 00h READ ACCESS PW2 WRITE ACCESS PW2 MEMORY TYPE Nonvolatile (SEE) B

Strany 74

DS1875PON Triplexer and SFP Controller76 ______________________________________________________________________________________Table 02h, Register BAh

Strany 75

DS1875Table 02h, Register BBh: TX-F ENABLE0 FACTORY DEFAULT 00h READ ACCESS PW2 WRITE ACCESS PW2 MEMORY TYPE Nonvolatile (SEE)

Strany 76

DS1875PON Triplexer and SFP Controller78 ______________________________________________________________________________________Table 02h, Register BCh

Strany 77

DS1875Table 02h, Register BEh: HBIAS FACTORY DEFAULT 00h READ ACCESS PW2 WRITE ACCESS PW2 MEMORY TYPE Nonvolatile (SEE)

Strany 78 - Table 02h, Register BDh: LTXP

DS1875PON Triplexer and SFP Controller8 _______________________________________________________________________________________PARAMETER SYMBOL CONDIT

Strany 79 - Full Scale

DS1875PON Triplexer and SFP Controller80 ______________________________________________________________________________________Table 02h, Register C0h

Strany 80 - Table 02h, Register C0h: DPU

DS1875Table 02h, Register C1h to C2h: RESERVED FACTORY DEFAULT 00h READ ACCESS PW2 WRITE ACCESS PW2 MEMORY TYPE Nonvolatile (S

Strany 81 - Table 02h, Register C4h: DAC1

DS1875PON Triplexer and SFP Controller82 ______________________________________________________________________________________Table 02h, Register C5h

Strany 82

DS1875Table 02h, Register C8h to C9h: MON5 SCALETable 02h, Register CAh to CBh: MON6 SCALETable 02h, Register CCh to CDh: MON7 SCALETable 02h, Registe

Strany 83

DS1875PON Triplexer and SFP Controller84 ______________________________________________________________________________________Table 02h, Register D8h

Strany 84

DS1875Table 02h, Register FBh to FCh: BIAS DAC FACTORY DEFAULT 8000h READ ACCESS PW2 WRITE ACCESS N/A MEMORY TYPE Volatile FBh

Strany 85

DS1875PON Triplexer and SFP Controller86 ______________________________________________________________________________________Table 02h, Register FEh

Strany 86 -  (PWM DAC + 1)

DS1875Table 03h Register DescriptionsTable 03h, Register 80h to FFh: PW2 EEPROM FACTORY DEFAULT 00h READ ACCESS PW2 WRITE ACCESS PW2

Strany 87

DS1875PON Triplexer and SFP Controller88 ______________________________________________________________________________________Table 05h Register Desc

Strany 88

DS1875Table 06h Register DescriptionsTable 06h, Register 80h to 9Fh: M4DAC LUT FACTORY DEFAULT 00h READ ACCESS PW2 WRITE ACCESS PW2

Strany 89

DS1875Note 1: All voltages are referenced to ground. Current into IC is positive, and current out of the IC is negative.Note 2: Digital inputs are at

Strany 90

DS1875PON Triplexer and SFP Controller90 ______________________________________________________________________________________Table 07h Register Desc

Strany 91 - Package Information

DS1875PON Triplexer and SFP Controller______________________________________________________________________________________ 91 FACTORY DEFAULT 00h

Strany 92 - Revision History

DS1875PON Triplexer and SFP ControllerMaxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim pr

Komentáře k této Příručce

Žádné komentáře