Rainbow-electronics MAX1618 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Rainbow-electronics MAX1618. Rainbow Electronics MAX1618 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 18
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
________________General Description
The MAX1618 precise digital thermometer reports the
temperature of a remote sensor. The remote sensor is a
diode-connected transistor—typically a low-cost, easily
mounted 2N3904 NPN type—that replaces conventional
thermistors or thermocouples. Remote accuracy is ±3°C
for multiple transistor manufacturers, with no calibration
needed. The MAX1618 can also measure the die temper-
ature of other ICs, such as microprocessors, that contain
an on-chip, diode-connected transistor.
The 2-wire serial interface accepts standard System
Management Bus (SMBus™) Write Byte, Read Byte, Send
Byte, and Receive Byte commands to program the alarm
thresholds and to read temperature data. The data format
is 7 bits plus sign, with each bit corresponding to 1°C, in
two’s complement format. Measurements can be done
automatically and autonomously, with the 16Hz conversion
rate or programmed to operate in a single-shot mode.
The thermostat mode configures the ALERT output as an
interrupt or as a temperature reset that remains active only
while the temperature is above the maximum temperature
limit or below the minimum temperature limit. The ALERT
output polarity in thermostat mode can be configured for
active high or active low. Fan control is implemented using
this ALERT output.
The MAX1618 is available in a small (1.1mm high) 10-pin
µMAX package.
________________________Applications
Desktop and Notebook Central Office
Computers Telecom Equipment
Smart Battery Packs Test and Measurement
LAN Servers Multichip Modules
Industrial Controls
____________________________Features
Single Channel: Measures Remote CPU
Temperature
No Calibration Required
SMBus 2-Wire Serial Interface
Programmable Under/Overtemperature Alarms
Overtemperature Output for Fan Control
(Thermostat Mode)
Supports SMBus Alert Response Accuracy
±3°C (+60°C to +100°C)
±5°C (-55°C to +120°C)
A (typ) Standby Supply Current
900µA (max) Supply Current in Autoconvert Mode
+3V to +5.5V Supply Range
Small 10-Pin µMAX Package
MAX1618
Remote Temperature Sensor
with SMBus Serial Interface
________________________________________________________________ Maxim Integrated Products 1
MAX1618
SMBCLK
ADD0 ADD1
V
CC
STBY
GND
ALERT
SMBDATA
DXP
DXN
INTERRUPT
TO µC
3V TO 5.5V
200
0.1µF
CLOCK
10k EACH
DATA
2N3904
2200pF
___________________Pin Configuration
1
2
3
4
5
10
9
8
7
6
ALERT
SMBDATA
SMBCLK
STBYDXN
GND
ADD1
ADD0
MAX1618
µMAX
TOP VIEW
V
CC
DXP
Typical Operating Circuit
19-1495; Rev 1; 12/99
PART
MAX1618MUB -55°C to +125°C
TEMP. RANGE PIN-PACKAGE
10 µMAX
Ordering Information
SMBus is a trademark of Intel Corp.
Patents Pending
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Zobrazit stránku 0
1 2 3 4 5 6 ... 17 18

Shrnutí obsahu

Strany 1 - Remote Temperature Sensor

________________General DescriptionThe MAX1618 precise digital thermometer reports thetemperature of a remote sensor. The remote sensor is adiode-conn

Strany 2

above VCC- 1V (typ) or below VDXN+ 50mv (typ), afault is detected and ALERT is asserted. ADC reads+127°C. Also, if the ADC has an extremely low differ

Strany 3

MAX1618Remote Temperature Sensor with SMBus Serial Interface______________________________________________________________________________________ 11R

Strany 4

Slave AddressesThe device address can be set to one of nine differentvalues by pin-strapping ADD0 and ADD1 so more thanone MAX1618 can reside on the s

Strany 5

introduces errors due to the rise time of the switched-current source.PC Board Layout1) Place the MAX1618 as close as practical to theremote diode. In

Strany 6

MAX1618Remote Temperature Sensor with SMBus Serial Interface14 ______________________________________________________________________________________6

Strany 7

MAX1618Remote Temperature Sensor with SMBus Serial Interface______________________________________________________________________________________ 15/

Strany 8

MAX1618Remote Temperature Sensor with SMBus Serial Interface16 ______________________________________________________________________________________i

Strany 9

MAX1618Remote Temperature Sensor with SMBus Serial Interface______________________________________________________________________________________ 17i

Strany 10

MAX1618Remote Temperature Sensor with SMBus Serial InterfaceMaxim cannot assume responsibility for use of any circuitry other than circuitry entirely

Strany 11

Autoconvertmode, averageMAX1618Remote Temperature Sensor with SMBus Serial Interface2 ________________________________________________________________

Strany 12

MAX1618Remote Temperature Sensor with SMBus Serial Interface_______________________________________________________________________________________ 3E

Strany 13

40-401 100TEMPERATURE ERRORvs. LEAKAGE RESISTANCE-20-30-100102030MAX1618 toc01LEAKAGE RESISTANCE (MΩ)TEMPERATURE ERROR (°C)10PATH = DXP TO GND AND CON

Strany 14

MAX1618Remote Temperature Sensor with SMBus Serial Interface_______________________________________________________________________________________ 51

Strany 15

MAX1618Remote Temperature Sensor with SMBus Serial Interface6 _______________________________________________________________________________________P

Strany 16

MAX1618Remote Temperature Sensor with SMBus Serial Interface_______________________________________________________________________________________ 7F

Strany 17

Low-Power Standby ModeStandby mode disables the ADC and reduces the sup-ply-current drain to 3µA (typ). Enter standby mode byforcing the STBY pin low

Strany 18

and does not go inactive until the temperature dropsbelow TLOW. Enable thermostat mode through the configuration reg-ister (Table 4), with one bit to

Komentáře k této Příručce

Žádné komentáře